Current transformer - use matters needing attention

115/120 V AC Voltage and Three-phase Phase small 240v electric motor
Specifications
1.Specifications1.3-phase asynchronous motors 
2.IEC standard 
3.OEM 
4.Voltage:50HZ &60HZ;380V&415V 

5.Protection class: IP54 
Operation of the current transformer, vice edge is not allowed to open. Because once open, have ac electric motor become primary side current excitation current, the magnetic flux and vice side voltage more than normal and endangers one's personal and equipment safety. Therefore, vice edge is not allowed to answer the fuse in the circuit, current transformer are not allowed in the runtime removed without bypass current meter, relay and other equipment. The connection mode ANP gost motor of current transformer load according to the receive operation requirement. The connection mode of the most commonly used for single-phase, three-phase star and incomplete star. Rated than the rating of the transformer and error change ratio KN refers to the rated voltage of the voltage transformer ratio Three phase motor and rated current of the current transformer ratio. The former is defined as the original winding rated voltage U1N and deputy while winding, the ratio of the rated voltage U2N; The ratio of the latter for rated current I1N to I2N.

Squirrel-cage asynchronous motor soft starter application - soft starter way of starting

electric motor 20hp aluminum body
Specifications
1.AC motor aluminum body
2.customized
3. 20 years manufacturing experience
4. competitive price,high quality

1 current-limiting starting: in the process of starting, limit the starting current does not exceed a certain value (Im), and then keep the output current, I < Im increased under the condition of voltage, until the rated voltage; The motor speed gradually increases, until the rated speed. Slope voltage starting 2: electric motor 12v 500w in electric vehicle motor the process of starting, the output torque of the motor with the increase of voltage, when starting to provide an initial starting voltage Us, then the output voltage from the Us started to grow in a certain slope, slope adjustable), motor accelerating. When the output voltage reaches up to Ur speed voltage, the motor is basically reach the rated speed. When the motor reaches the rated speed, make the output voltage at rated voltage. 3 starting torque control: use in overloading starting torque control, it is the starting torque of the motor from small to large linear rise. 


Y2 series electric motor wholesale

Specifications
1. effiency: IE2 and IE1
2. 20 years manufacturing experience
3. 12 months guarantee

4. low noise and vibtration

It has the advantage of smooth starting, flexibility is good, have better protection to drag system, its purpose is to protect the drag system, extend the service life of the drag system. 4 starting torque and kick control: at the beginning of the start stage, let the thyristor within a very short time conduction after all fall, according to the original set the value of the linear rise again, enter the starting with constant current. Starting torque and kick control and torque control starting similar is also used in overloading starting, the difference is with acmotortrading.blogspot.com a sudden jump in starting torque to overcome static torque of the motor, then smooth torque rise, shorten the start-up time. Starting: 5 voltage control the voltage control starting is used for light load starting of occasions, in guarantee starting pressure drop the maximum starting torque motor, as much as possible to shorten the start-up time, is the optimal way of light load soft starter.

Sensorless brushless dc motor control - back emf method

Stator Motors Rotor
Specifications
1. 20 years manufacturing experience
2. competitive price,high quality

"The potential laws" is by far the most mature, the most effective, is also the most common and most widely application a rotor position signal detection method. The basic principle of this method is to ignore the influence of fan motor permanent magnet brushless dc motor armature reaction, by detecting "disconnect" (inverter bridge power device is up and down in that phase) off of the back emf zero, in order to get the rotor's six key position signal, and use this as reference, in turn trigger conduction six power tube, drive motor running. This method is often used in the wholesalemotor.blogspot.com armature winding adopts y connection of "three phase six - 120 ° square wave type" driven permanent magnet brushless dc motor (because of square wave motor is just a number of discrete key rotor position signals). 

Y series totally enclosed protect Asynchronous motor
Specifications
1. 20 years manufacturing experience
2. 12 months guarantee
3. low noise and temperature rise

4. high starting torque
Figure 1 (a) and (b) are given a Taipei wave motor of main circuit, the back emf waveform and trigger a composite state of inverter power devices. The figure 1 (b) shows that at any moment of the inverter power supply, there is always a in ac motor the upper and lower bridge arm are in the off state, namely the phase winding motor is impending, so the phase voltage is equal to the induced potential of the phase winding. In ignore the armature reaction of air-gap magnetic field under the lamination premise of the impact, can be thought of the induced electric potential is equal to the phase winding back emf. Detecting the back emf zero moment, and delay, if appropriate, can get the right trigger time of power device, and the electric potential zero point can be obtained by phase voltage of the voltage or testing.