显示标签为“
small diesel engine”的博文。
显示所有博文
显示标签为“
small diesel engine”的博文。
显示所有博文
Stator And Rotor ac induction motor parts
Specifications
1. 20 years manufacturing experience
2. competitive price,high quality
3. Material: silicon steel
Wall switch off the ground should be www.facebook.com/guohong.trading 1.3 meters, 0.3 mira line wall socket switch should be 2-3 m above the floor. Electricity meter from the ground should be 1.4-1.8 meters into the line the ground should be 2.7 meters from the diesel engine path, a, secondary roads, electric drive, the main river, low voltage circuit, special cableway, etc, should not have joint. Ming with plastic sheath line is mainly used for indoor installation, may not be directly into the plaster layer in the dark with laying. Wire wear tube general requirements tube total cross- sectional area of the wire (including insulation) is not more than 40% of electric water pump line pipe inner sectional area. Wire tube shall have joint, joint should be within the junction box; Different power supply circuit and voltage loop, as spare circuit, line work lighting 3 phase induction motor and emergency lighting shall be installed in the same tube. Pipe for steel pipe (tube), the same communication circuit wiring must wear the same tube, do not allow a wire through a steel tube.
CCC CE ROHS UL VDE Certification and 115/120 V AC Voltage 220V&120V induction motor
Specifications
1. Specifications1.3-phase asynchronous motors
2. IEC standard
3. OEM
4. Voltage:50HZ &60HZ;380V&415V
5.Protection class: IP54
A root canal on the conductor shall not exceed small diesel engine eight. Steel (iron) for pipe, the pipe must be reliable grounding. Pipe for steel pipe (tube), the line must add plastic on alternator generator both ends of pipe. Wire wear tube length of more than 30 meters (half hard tube) which should be installed between the junction box. Wire wear tube length more than 40 meters (iron pipe) which should be installed between the junction box. single phase induction motor Wire wear tube, there is a curved line pipe length no more than 20 meters. Which should be installed between the junction box. Wire wear tube, there are two curved line pipe length is not more than 15 meters. Which should be installed between the junction box. Wire wear tube, there are three bending tube length is not more than 8 meters. Which should be www.dongfeng- motor.com installed between the junction box. When using polyphase power supply, wire of the same building insulation color selection should be consistent, namely protect wire (PE) should be green/yellow double-color wire, neutral wire (N) line for the light blue; Line L1 - yellow, L2 - green, L3 - red. Single-phase power supply switch line is red, after the switch general USES white or yellow. magnetic generator Joint position of the wire should not be in the insulator fixed place, joint location away from the wires should be above 0.5 meters, hampering binding wire and broken.
AC motor aluminum 2800 rpm motor fan cover
Specifications
1. Customised
2. good quality
3. Surface treatment: Galvanize
4. AC motor
The requirements of the asynchronous motor starting 1, starting torque of motor is large enough. 2, on the premise of certain size starting torque, starting current as small as possible. 3, starts the required equipment is simple, easy to operate. 4, rotor power loss in the process of start as small as possible. Squirrel-cage asynchronous motor start. Direct start that start with voltage on the stator winding of the motor rated voltage. Three-phase asynchronous motor direct start (a) meet the conditions of electric motor parts 1, capacity under the 7.5 KW motor can be used. 2, motor at starting moment www.dongfeng-motor.com caused by the power grid voltage diesel generator set drop is not more than 10% of the power supply voltage is normal, for not often small diesel engine start three phase induction permanent magnet lamination machine generator motor the motor can be up to 15%. 3, available empirical formula rough estimates whether the permanent magnet generator motor can electricalmotor1.blogspot.com be directly started. Advantages: the boot device is electric generator simple, the startup time is short, starting operation simple, reliable, the cost is low. Disadvantages: the motor and power grid has a certain impact.
Y2 series 0.75kW (1HP) AC Motor for Speed Control
Specifications
1. effiency: IE2 and IE1
2. 20 years manufacturing experience
3. 12 months guarantee
4. low noise and vibtration
For refrigeration equipment repair, time is the second step of the general fault maintenance. The first is to suppress (not including the compressor or change tube) in determining the pipeline without leakage, the next step is to fit. There are two commonly used methods: 1, use the vacuum pump. You can also use a compressor to replace the vacuum pump. Time is longer than generator price with the vacuum pump is a few longer, because of the relative likelihood () compressor exhaust two (amount) to some smaller than vacuum diesel engine pump. On the fridge process pipe connected to a job with a pressure gauge valve, one head welding on the compressor, the other end with a liquid pipe connection on the vacuum pump, open the table method (valve) the door, start the vacuum pump or external compressor, start time, when there is no gas discharge vent on the vacuum pump, took over. 2, to use own compressor to itself. This method is very suitable for go out to repair, need not with vacuum pump. The method is: if the filter is on double tail, mouth open work (the original is www.dongfeng-motor.com welding die), start the compressor, there will be a lot of air from the mouth, when the mouth no gas discharge, the mouth with the hand, unplug the power supply. (be sure to pay attention to safety) open the charging the practice to the system such as refrigerating fluid, when the filter working gas discharge. In the mouth of tongs death, gas welding is used after sealing the mouth.????
motor lamination three phase induction wound rotor
Specifications
1. Lamination of electric motor
2. IP54 class F
3. 100% copper
4. silicon steel stamping
5.stunning performance
Add liquid small diesel engine cooling: cooling liquid, add fluid tube, table after the valves are connected, open the charging the practice period of open (loosen) the end of the charging tube when the tube had cooling liquid discharge head, tighten the method of block (LAN). Open the table on the compressor valve, had better add liquid cooling liquid cylinders upside down, ac synchronous generator when the table shows 4 diesel generator set kg pressure, close the charging valve. The refrigerator electricity, then the pressure of the table with the work single phase induction motor of machine down. When the clock stability have a look at the pressure, generally between zero point three to zero point 8 belong to normal pressure. The static plus 4 kg is based on the refrigerator when the low pressure of static pressure is 4 times at work. As the refrigerator working time increased, the temperature in the oven has been falling, filled volume of the normal, running after a period of time on the muffler should meet (knot), temperature and environmental temperature is the same as the filter or a touch more heat for exactly. If acmotortrading.blogspot.com on the muffler by frosted) (cooling fluid add much, off some, open the charging valve slowly, let while observing muffler, see the frost charging valve shut. If a long time running back up the (gas) pipe temperature is not cool or without dew, open the charging valve and adding some refrigeration fluid. Practice has proved that the choice of low voltage motor fuse and maintenance fuse for low voltage motor phase short circuit, single phase short circuit fault and squirrel cage induction motor overload protection device is simple and effective. But if the fuse type and parameter selection, improper or disadvantage in operation and maintenance, also can not meet the expectations of protection.
